AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateStyles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
See the difference
Before
After
Before
After
Before
AfterHow Much Does Heat Pump Installation Cost in Davie?
Heat pump installation in Davie typically costs between $3,500 and $7,500 for a full system, with most single-family homes landing in the $4,500 to $6,000 range once the air handler, outdoor unit, and line set are all accounted for. A straight swap of an existing heat pump with matching capacity often runs toward the lower end, while a first-time installation or a size upgrade pushes toward the top. The written estimate we prepare after seeing your home, ductwork, and electrical setup sets the final price.
We’re Davie AC Repair, and we install and service equipment from nine major manufacturers. That matters on a job like this because a heat pump isn’t a one-brand product category. A Goodman, a Trane, a Daikin, and a Lennox all install differently, and the right choice for your house depends on your ducts, your sun exposure, and your budget, not on which manufacturer gives a contractor the best incentive. You can read more about how we work on our Davie AC Repair home page.
Key Takeaways
- Typical installed cost in Davie: $3,500 – $7,500, most commonly $4,500 – $6,000.
- Equipment brand and efficiency tier is the single biggest cost lever, often a $2,000 spread on the same house.
- Ductwork changes, electrical upgrades, and line set replacement are usually what separate a low bid from a high one.
- We’re certified on Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard.
- Estimates are free. Call (833) 548-1941. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Heat Pump Installation Cost Breakdown (2026)
Here’s how the money usually splits on a heat pump replacement in Davie. These are typical estimated ranges for our market in 2026, not a quote for your specific home. Your written estimate is what sets the price.
| Line Item | Typical Estimated Range | What It Covers |
|---|---|---|
| Heat pump system (outdoor unit + air handler) | $2,200 – $4,800 | Equipment only. Budget-tier units sit at the low end, high-efficiency variable-speed units at the high end. |
| Labor and installation | $800 – $1,600 | Removal of old equipment, setting the new unit, brazing line sets, evacuation, charging, startup. |
| Line set replacement | $250 – $700 | New refrigerant lines when the existing ones are undersized, kinked, or the wrong refrigerant type. |
| Electrical work | $200 – $900 | Disconnect replacement, breaker and wire sizing for the new unit, permit-related electrical inspection. |
| Duct modifications | $300 – $1,500 | Resizing plenums, adding returns, sealing leaks, correcting a duct system built for a different capacity. |
| Thermostat and controls | $0 – $450 | Reusing your existing thermostat costs nothing. A communicating or smart thermostat adds to the top. |
| Permit and inspection | $150 – $450 | Most Florida municipalities require a permit for a heat pump changeout. Ask the town what applies to your address. |
| Drain pan, float switch, secondary drain | $100 – $350 | Condensate management. Important in South Florida, where a heat pump pulls a lot of water in cooling mode. |
Add those up and you land inside the $3,500 – $7,500 band. A like-for-like swap in a home with clean, correctly sized ductwork sits near the bottom. A home where the previous system was undersized, the ducts leak, or the electrical panel needs work climbs toward the top. The spread between the cheapest bid and the highest on the same house is often $3,000 or more, and almost none of that spread is the equipment itself. It’s the labor and the supporting work. When you compare estimates, compare line items, not bottom-line totals.
What Affects Heat Pump Installation Pricing in Davie
Six things move the number more than anything else on a heat pump job here.
- System size and load calculation. A heat pump has to be sized to the house, not to the old unit. A proper load calculation looks at square footage, window area, insulation, and orientation. Davie homes with large west-facing glass or older single-pane windows often need a slightly larger system than a same-size house a few blocks away, and one ton of capacity is roughly $800 – $1,200 of the total. Oversizing is a real problem in our climate: it short-cycles, dehumidifies poorly, and wears out faster.
- Equipment tier and brand. A Goodman single-stage unit and a Trane variable-speed unit are both heat pumps, but they’re not the same product and they don’t cost the same. The gap between the entry tier and premium high-efficiency tier on the same house commonly runs $1,500 – $2,500. Efficiency ratings matter here: our cooling season is long, and a higher-efficiency unit can pay back over time, but only if the ductwork supports it. The cheapest equipment on bad ducts is a waste of money.
- Ductwork condition. This is the item homeowners most often get surprised by. A heat pump moving 3 tons of air through ducts built for 2.5 tons will underperform no matter how good the equipment is. Sealing, resizing, or adding a return can add $300 – $1,500, and in a home with a flex-duct system in the attic that’s been baking for years, it’s often the smartest money on the job.
- Electrical service and disconnect. Heat pumps draw serious amperage, and older homes around Davie sometimes have a panel that won’t support the new unit without a change. That can mean $200 for a disconnect and whip, or considerably more if the panel itself needs work by a licensed electrician. We’ll flag it on the estimate so there are no surprises.
- Line set and refrigerant type. If your existing line set is sized for the older refrigerant and the new unit uses a different one, the lines get replaced. Kinked or buried lines get replaced too. This is a $250 – $700 item and it’s not negotiable on a proper installation.
- Access and location. A ground-level pad with a clear path to the air handler is a straightforward day. An air handler in a tight attic with a steep pull-down stair, or an outdoor unit tucked behind a fence with no gate, adds labor. We’d rather tell you that up front than discover it halfway through.
Heat Pump vs. Straight AC in Davie: What the Price Difference Actually Buys
A heat pump costs roughly $400 – $900 more than a comparable straight cooling system in the same size and efficiency tier. What you get for that premium is heating. Instead of a separate furnace or electric resistance strip heat, the heat pump reverses its refrigerant cycle in cooler months and moves heat into the house rather than out. In a mild-winter climate like ours, that’s usually all the heating a home needs.
This is where a lot of Davie homeowners get steered wrong. A contractor who only sells air conditioners will quote you an AC and a strip-heat kit, and the strip heat is expensive to run. A contractor who sells a single furnace brand will quote a furnace whether or not a heat pump fits your home. We install and repair both sides of the equation, so the recommendation is about your house. If a heat pump makes sense, we’ll say so. If your existing ductwork or electrical service makes a straight AC the smarter buy, we’ll say that too. Repair first, replace only when it makes sense for you.
What a Heat Pump Installation Actually Involves
Understanding the sequence helps you read an estimate. A typical installation runs one to two days depending on scope.
- Load calculation and equipment selection. We measure the house, check insulation and window area, and size the system. Then we match the equipment to your budget across the brands we carry.
- Permit. Most cities in Broward County require a mechanical permit for a heat pump changeout. We’ll tell you what applies and handle the paperwork where we can.
- Removal and recovery. Old refrigerant is recovered, not vented. It’s a legal requirement and a good sign of a professional job.
- Setting the equipment. New pad and outdoor unit, air handler in place, vibration isolation, level and clear of debris.
- Line set and electrical. New or verified refrigerant lines, brazed connections, pressure test, evacuation, and charging to the manufacturer’s spec. Electrical disconnect and whip replaced as needed.
- Duct connection and sealing. Plenum transitions, sealing at the air handler, checking return capacity.
- Condensate management. Drain pan, primary and secondary drains, float switch. In our humidity, a stopped drain can mean ceiling damage fast.
- Startup and commissioning. Refrigerant charge verified, airflow measured, temperature split checked, thermostat configured, and the system run through a full heating and cooling cycle before we leave.
One safety note: the refrigerant and electrical work on a heat pump are not homeowner tasks. Refrigerant handling requires certification and the wrong charge level will destroy a compressor. Electrical connections at the disconnect and air handler carry enough current to be genuinely dangerous. We’re state-licensed and insured for this work, and we’d rather you call us than open the disconnect cover.
How to Save on Heat Pump Installation
There’s no secret discount code. The savings come from making good decisions before the crew shows up.
- Get the load calculation done. It’s the cheapest part of the job and it prevents the most expensive mistake. Oversized equipment costs more up front and fails sooner.
- Repair the ducts first if they leak. Sealing $300 – $1,500 worth of ductwork can let you buy a smaller, less expensive system and still get better comfort. A heat pump on leaking ducts is money out the window.
- Compare line items, not totals. The $3,800 bid and the $6,200 bid on the same house usually differ because one leaves out the line set, the permit, or the duct fixes. Ask what’s excluded.
- Consider mid-tier efficiency. The jump from entry to mid-tier is often where the real value sits. The jump from mid-tier to the top-of-line variable-speed unit costs more and saves less unless your ducts and insulation are in good shape.
- Ask about your existing thermostat and controls. Reusing a working thermostat saves $250 – $450. We’ll tell you honestly whether your current one is compatible.
- Get your estimates free. We don’t charge for an estimate and the price is set by the written estimate, not by a sales visit. Call (833) 548-1941.
Is It Cheaper to Repair or Replace a Heat Pump in Davie?
Repair is usually the right call when the unit is under about ten years old and the repair is a compressor, reversing valve, or control board rather than a major system failure. Heat pump repair in Davie typically runs $150 – $700, which is a fraction of a replacement. Replacement makes more sense when the unit is old, the repair is a compressor or coil replacement at a large fraction of new-system cost, or the system uses a refrigerant that’s being phased out. We’ll price the repair honestly and tell you when replacing is the better spend. We won’t push a replacement you don’t need.
Does Brand Choice Change the Price?
Yes, and by more than homeowners expect. Across the nine brands we’re certified on, the same nominal capacity in the same efficiency tier can vary by several hundred dollars, and moving between tiers is a bigger jump than moving between brands. Goodman and Rheem generally sit toward the value end. Carrier, Trane, Lennox, Bryant, and American Standard tend toward the premium end, with Daikin and York filling out the middle. None of them is a bad product. The question is which one fits your home, your ducts, and your budget. Whether it’s a Goodman or a Trane, we know it.
Why Homeowners in Davie Call Us
Davie AC Repair is a multi-brand HVAC specialist, and heat pumps are one of the few categories where the name on the truck matters less than the breadth behind it. We work on nine brands because we don’t have an exclusive dealer agreement that biases the diagnosis. Our technicians have up to 15 years of experience, and we handle both cooling and heating, so you’re not calling a separate contractor for each system. Nine brands. Two systems. One call.
The practical upshot: we can quote you a heat pump from the brand that fits your situation, not the one we’re contractually obligated to move. We can repair the system you already own. And when the answer is a straight AC rather than a heat pump, we’ll tell you. Straight answers on what your HVAC actually needs.
FAQs – Heat Pump Installation Cost
How much does heat pump installation cost in Davie in 2026?
Heat pump installation in Davie typically runs $3,500 – $7,500, with most single-family homes landing around $4,500 – $6,000. The written estimate sets the final price. Call (833) 548-1941 for a free estimate.
Is it cheaper to repair or replace a heat pump?
Repair usually wins when the unit is under about ten years old and the failure is a control board, reversing valve, or fan motor – heat pump repair typically runs $150 – $700 versus a full replacement at $3,500 – $7,500. Replacement makes sense when the compressor or coil is gone. We’ll price both and let you decide. Call (833) 548-1941 for an exact quote – estimates are free.
How much does a heat pump cost versus a straight AC in Davie?
A heat pump costs about $400 – $900 more than a comparable straight cooling system in the same size and efficiency tier. The premium buys you heating without a separate furnace or strip-heat kit. For a typical Davie home, that’s usually the better long-term spend. Call (833) 548-1941 to talk through which fits your house.
Do I need a permit to install a heat pump in Davie?
Most Florida municipalities require a mechanical permit for a heat pump changeout, typically $150 – $450. Ask the town’s building department what applies to your address, and we’ll handle the paperwork where we can. Call (833) 548-1941 with questions about your project.
Can you install a heat pump the same day?
Same-day installation isn’t realistic for a full heat pump job – plan on one to two days. We answer 24/7, and we dispatch fast from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (833) 548-1941 to schedule your free estimate.
Where We Work
We install and service heat pumps throughout Davie and the surrounding Broward County area. Whether you’re near the Seminole Classic Casino end of town or out past Flamingo Gardens, the climate and housing stock are similar enough that the pricing bands on this page hold up. Homes with older ductwork, large west-facing glass, or a panel that’s maxed out will always sit toward the top of the range.
Get a Free Heat Pump Installation Estimate
If you’re weighing a heat pump against a straight AC, or you’re not sure whether your current system is worth repairing, call us. We’ll run a load calculation, walk your ducts, and give you a written estimate with line items you can compare. If a brand you don’t recognize ends up being the right fit, we’ll tell you – that’s what nine-brand certification actually means. Call (833) 548-1941. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free, and the written estimate sets the final price.
Pricing reflects the Davie market as of 2026. Davie AC Repair offers free estimates – call (833) 548-1941.
Written by the team at Davie AC Repair.
What Our Customers Say
"Two other companies told me I needed a whole new system. He put gauges on it, found a leak at a fitting on the line set, repaired it and recharged. That was 14 months ago and it's still holding."
- Alma Martinez"Blower motor on a 12 year old furnace. He gave me the honest math on repair versus replace and did not push me toward the bigger ticket. We repaired it and it's been fine."
- Tracy Reed"Contactor was pitted and chattering. Cheap part, quick fix, and he showed me the burn on the old one so I could see for myself."
- Jason Barrett